Original Posted By: Michael Perez
Pietenpol-List: A. Spruce and stainless hardware
Pietenpol-List: A. Spruce and stainless hardware
Original Posted By: airlion
Re: Pietenpol-List: Fw: Gardiner and his Pietenpol, December 2009
Original Posted By:> Susan Mason
That would be good...JackDSMSent from my iPhoneOn Dec 16, 2009, at 5:22 PM, airlion wrote:> Hey listers, Has anyone done a stress analysis for the pietenpol? I > have a friend here in Lagrange that is an engineer and used to work > for Lockheed. He says that he can do a stress test on my Piet. I > will let ya'll know the results. Cheers, Gardiner>> ----- Forwarded Message ----
That would be good...JackDSMSent from my iPhoneOn Dec 16, 2009, at 5:22 PM, airlion wrote:> Hey listers, Has anyone done a stress analysis for the pietenpol? I > have a friend here in Lagrange that is an engineer and used to work > for Lockheed. He says that he can do a stress test on my Piet. I > will let ya'll know the results. Cheers, Gardiner>> ----- Forwarded Message ----
Re: Pietenpol-List: A. Spruce and stainless hardware
Original Posted By: Michael Perez
I haven't checked for that specific part number, but generally speaking, there will be different suffix letters to describe the different materials. You'd need to look at that actual specification to see what it says.If all you know is that it's stainless, be advised that there's a lot of stainless out there that's 300 series annealed, with about a 27 to 35 ksi yield and 70 to 80 ksi ultimate strength. Be very cautious.David Paule ----- Original Message -----
I haven't checked for that specific part number, but generally speaking, there will be different suffix letters to describe the different materials. You'd need to look at that actual specification to see what it says.If all you know is that it's stainless, be advised that there's a lot of stainless out there that's 300 series annealed, with about a 27 to 35 ksi yield and 70 to 80 ksi ultimate strength. Be very cautious.David Paule ----- Original Message -----
Re: Pietenpol-List: Fw: Gardiner and his Pietenpol, December 2009
Original Posted By: _airlion_ (mailto:airlion(at)bellsouth.net)
Subject: Re: Pietenpol-List: Fw: Gardiner and his Pietenpol, December 2009I think we would all like to see itJohnIn a message dated 12/16/2009 9:06:38 P.M. Eastern Standard Time, dpaule(at)frii.com writes:Results, heck - post the entire analysis!Thanks!David PauleP.S. Advise him to reference ANC-18. It's available on the West Coast Piet site.----- Original Message -----
Subject: Re: Pietenpol-List: Fw: Gardiner and his Pietenpol, December 2009I think we would all like to see itJohnIn a message dated 12/16/2009 9:06:38 P.M. Eastern Standard Time, dpaule(at)frii.com writes:Results, heck - post the entire analysis!Thanks!David PauleP.S. Advise him to reference ANC-18. It's available on the West Coast Piet site.----- Original Message -----
Pietenpol-List: Re: A. Spruce and stainless hardware
Original Posted By: "Cuy, Michael D. (GRC-RXD0)[ASRC Aerospace Corporation]"
We noticed the postings in the Pietenpol forum regarding the rated strength ofthe MS24694 screws stocked by Aircraft Spruce. The rated strength of MS24694 steelscrews is 125,000 PSI, and the rated strength of MS24694C stainless steelscrews is 85,000 PSI. If anyone has any questions regarding these screws pleaselet us know. Aircraft Spruce Customer Service Dept.custsvc(at)aircraftspruce.comRead this topic online here:http://forums.matronics.com/viewtopic.p ... __________
We noticed the postings in the Pietenpol forum regarding the rated strength ofthe MS24694 screws stocked by Aircraft Spruce. The rated strength of MS24694 steelscrews is 125,000 PSI, and the rated strength of MS24694C stainless steelscrews is 85,000 PSI. If anyone has any questions regarding these screws pleaselet us know. Aircraft Spruce Customer Service Dept.custsvc(at)aircraftspruce.comRead this topic online here:http://forums.matronics.com/viewtopic.p ... __________