Original Posted By: "Douwe Blumberg"
Yes, my email was hacked!! I apologize for the emails which were sent over the last couple of days.Douwe________________________________________________________________________________
Pietenpol-List: spam apology
Pietenpol-List: spam apology
Original Posted By: airlion
Yes, my computer was hacked. sorry for the spam messages everyone's beengetting. I was away with my phone off and returned to like thirty messagessaying "hey was your computer hacked?"Sorry.Douwe________________________________________________________________________________Date: Thu, 20 Sep 2012 15:40:18 -0700 (PDT)
Yes, my computer was hacked. sorry for the spam messages everyone's beengetting. I was away with my phone off and returned to like thirty messagessaying "hey was your computer hacked?"Sorry.Douwe________________________________________________________________________________Date: Thu, 20 Sep 2012 15:40:18 -0700 (PDT)
Pietenpol-List: Re: spam apology
Original Posted By: Isablcorky(at)aol.com
DouweNo need to apologize. This is one of the hazards of the digital age, sort of likeburnt toast.DaveRead this topic online here:http://forums.matronics.com/viewtopic.p ... __________
DouweNo need to apologize. This is one of the hazards of the digital age, sort of likeburnt toast.DaveRead this topic online here:http://forums.matronics.com/viewtopic.p ... __________
Re: Pietenpol-List: Re: spam apology
Original Posted By: Michael Perez
Subject: Re: Pietenpol-List: Re: spam apologyIn a message dated 9/20/2012 8:11:58 P.M. Central Daylight Time, dgaldrich(at)embarqmail.com writes:--> Pietenpol-List message posted by: "dgaldrich" DouweNo need to apologize. This is one of the hazards of the digital age, sort of like burnt toast.DaveRead this topic online here:http://forums.matronics.com/viewtopic.p ... 83670Can't bring it downDaddy________________________________________________________________________________Date: Fri, 21 Sep 2012 04:35:24 -0700 (PDT)
Subject: Re: Pietenpol-List: Re: spam apologyIn a message dated 9/20/2012 8:11:58 P.M. Central Daylight Time, dgaldrich(at)embarqmail.com writes:--> Pietenpol-List message posted by: "dgaldrich" DouweNo need to apologize. This is one of the hazards of the digital age, sort of like burnt toast.DaveRead this topic online here:http://forums.matronics.com/viewtopic.p ... 83670Can't bring it downDaddy________________________________________________________________________________Date: Fri, 21 Sep 2012 04:35:24 -0700 (PDT)
Re: Pietenpol-List: spam apology
Original Posted By: Michael Perez
Re: Pietenpol-List: spam apology
Original Posted By: Michael Perez
Re: Pietenpol-List: NAS3 Assembly Bolts
Original Posted By: Michael Perez
He has a Marvel Schebler=85=85.different carb, different manufacturerOn Sep 21, 2012, at 7:10 AM, Michael Perez wrote:> > It sounds like you have a NAS3A - something. The 3B does not have the mixture control and that location is just blocked off with an aluminum plate. There are no internals inside at all. You can remove the mixture hardware and block it off, but I am not sure how/if you would need to re-name the carb. If you decide later to go back, or sell the carb., just leave the name the same and reassemble it. > > To answer you question more directly, the mixture would need to be wired full open, (rich) to the nearest bolt, nut, etc.> > Michael Perez> Pietenpol HINT Videos> Karetaker Aero> www.karetakeraero.com> > > > ________________________________________________________________________________Date: Fri, 21 Sep 2012 05:50:16 -0700 (PDT)
He has a Marvel Schebler=85=85.different carb, different manufacturerOn Sep 21, 2012, at 7:10 AM, Michael Perez wrote:> > It sounds like you have a NAS3A - something. The 3B does not have the mixture control and that location is just blocked off with an aluminum plate. There are no internals inside at all. You can remove the mixture hardware and block it off, but I am not sure how/if you would need to re-name the carb. If you decide later to go back, or sell the carb., just leave the name the same and reassemble it. > > To answer you question more directly, the mixture would need to be wired full open, (rich) to the nearest bolt, nut, etc.> > Michael Perez> Pietenpol HINT Videos> Karetaker Aero> www.karetakeraero.com> > > > ________________________________________________________________________________Date: Fri, 21 Sep 2012 05:50:16 -0700 (PDT)