Page 1 of 1
Posted: Fri Aug 28, 2009 3:11 pm
by matronics
Original Posted By: Jeff Boatright
Pietenpol-List: Almost time to start covering this thing
Posted: Fri Aug 28, 2009 3:17 pm
by matronics
Original Posted By: Rick Holland
Subject: Pietenpol-List: Almost time to start covering this thing
Pietenpol-List: Re: Almost time to start covering this thing
Posted: Fri Aug 28, 2009 4:36 pm
by matronics
Original Posted By: "Mike Whaley"
Rick I am glad to hear your intent of using Latex-I am not at all satisfied withthe coverage I got from the Poly products I have had including the red I didthe fuselage in with Polytone. i no doubt tried to get by using too little butI am seriously considering going over at least the rear portion of the fuselagewith some Red latex if I can get them to mix a good match of color.( I havenever checked to see if it's available in deep red) I managed to drip a dropof white latex in the side as I was using it to seal some wood and I thoughtif I wiped it within 5 minutes with a wet rag it would be gone. no such luck.I still have a small white smudge.and if it stays that good by accident I don'tknow why it wouldn't do just fine if I'd wash the dust off and let it dry androll a coat or two on -on purpose.RaymondRead this topic online here:
http://forums.matronics.com/viewtopic.p ... __________
Re: Pietenpol-List: Almost time to start covering this thing
Posted: Sat Aug 29, 2009 8:25 am
by matronics
Original Posted By: Michael Perez
Re: Pietenpol-List: Almost time to start covering this thing
Posted: Sat Aug 29, 2009 8:27 am
by matronics
Original Posted By: Michael Perez
Re: Pietenpol-List: Re: Almost time to start covering this thing
Posted: Sat Aug 29, 2009 9:45 am
by matronics
Original Posted By: Jim Markle
RE: Pietenpol-List: A special Pietenpol
Posted: Sat Aug 29, 2009 10:55 am
by matronics
Original Posted By: owner-pietenpol-list-server(at)matronics.com
Better check your tool chest, Dan! But that's one beautiful engine...Gary BootheCool, Ca.PietenpolWW Corvair ConversionTail done, Fuselage on gear(13 ribs down.)-----Original Message-----
RE: Pietenpol-List: Almost time to start covering this thing
Posted: Mon Aug 31, 2009 5:05 pm
by matronics
Original Posted By: owner-pietenpol-list-server(at)matronics.com
Nice report, Ben. Thanks! Don't be bashful about sending pics...Gary BootheCool, Ca.PietenpolWW Corvair ConversionTail done, Fuselage on gear(13 ribs down.)-----Original Message-----
RE: Pietenpol-List: Almost time to start covering this thing
Posted: Mon Aug 31, 2009 8:25 pm
by matronics
Original Posted By: "Richard Schreiber"
Subject: RE: Pietenpol-List: Almost time to start covering this thingYou are SO RIGHT Ben Charvet about watching how wide the fabric rolls are if youwant to use the 'overlap' method of coveringyour wings. (otherwise you need to have an envelope sewn together to make thenarrower rolls fit) Superflite carried the 1.7 oz stuff in the widest width so I went with them formy fabric and glue--the rest was finished in Randolph dope. Another savings-- we don't need the PMA certified stamp on our fabric (plus itall comes from the same mill no matter who you buy fabric from) so Superflite (used to anyway) carry the uncertified wide stufffor less than the factory built plane guys who needthe certified fabric. ________________________________________________________________________________
Re: Pietenpol-List: Almost time to start covering this thing
Posted: Tue Sep 01, 2009 3:53 pm
by matronics
Original Posted By: stephen labash
Subject: Re: Pietenpol-List: Almost time to start covering this thingJim, do you have a schedule or start date in mind? I have not been to any of the covering seminars yet but would like to see yours mid way or in progress of covering to get an idea of how its posta be did. So I can did minesthe right way to.John________________________________________________________________________________