Original Posted By: "skellytown flyer"
You know, I tried to go back and edit this message after I posted to correct themisspell - but it didn't seem to fxi ti...Lorin--------Lorin MillerWaiex N81YXGN-1 N30PPRead this topic online here:http://forums.matronics.com/viewtopic.p ... ___Subject: Pietenpol-List: engine run-up
Pietenpol-List: engine run-up
Original Posted By: Jim Markle
Well I got my wings back off and rolled my GN-1 out in the sunshine today and gotit tied down and ran the Corvair D.J. built up. it sounds strong and smoothso far -I got the timing what looks like close but in the bright sunshine itis difficult to see the marks really well so I'm going to check it again aboutdusk. but it sure seems to pull Strong so far.I didn't go full open for overa few seconds but I believe it will pretty easily turn 2850 or more.and that shoulddrag this thing into the air pretty well.oil pressure seems to stay around38 or so even pretty warmat idle. head temps never went over about 284 sofar. RaymondRead this topic online here:http://forums.matronics.com/viewtopic.p ... ______Date: Fri, 27 Aug 2010 18:50:27 -0500 (GMT-05:00)
Well I got my wings back off and rolled my GN-1 out in the sunshine today and gotit tied down and ran the Corvair D.J. built up. it sounds strong and smoothso far -I got the timing what looks like close but in the bright sunshine itis difficult to see the marks really well so I'm going to check it again aboutdusk. but it sure seems to pull Strong so far.I didn't go full open for overa few seconds but I believe it will pretty easily turn 2850 or more.and that shoulddrag this thing into the air pretty well.oil pressure seems to stay around38 or so even pretty warmat idle. head temps never went over about 284 sofar. RaymondRead this topic online here:http://forums.matronics.com/viewtopic.p ... ______Date: Fri, 27 Aug 2010 18:50:27 -0500 (GMT-05:00)
Pietenpol-List: Re: engine run-up
Original Posted By: "Dan P"
Congratulations. That's great!!Sent from my iPhoneOn Aug 27, 2010, at 4:38 PM, "skellytown flyer" wrote:> > Well I got my wings back off and rolled my GN-1 out in the sunshine today andgot it tied down and ran the Corvair D.J. built up. it sounds strong and smoothso far -I got the timing what looks like close but in the bright sunshine itis difficult to see the marks really well so I'm going to check it again aboutdusk. but it sure seems to pull Strong so far.I didn't go full open for overa few seconds but I believe it will pretty easily turn 2850 or more.and thatshould drag this thing into the air pretty well.oil pressure seems to stay around38 or so even pretty warmat idle. head temps never went over about 284 sofar. Raymond> > > > > Read this topic online here:> > http://forums.matronics.com/viewtopic.p ... 321#310321> > > > > > > > > > ________________________________________________________________________________Subject: Pietenpol-List: Re: engine run-up
Congratulations. That's great!!Sent from my iPhoneOn Aug 27, 2010, at 4:38 PM, "skellytown flyer" wrote:> > Well I got my wings back off and rolled my GN-1 out in the sunshine today andgot it tied down and ran the Corvair D.J. built up. it sounds strong and smoothso far -I got the timing what looks like close but in the bright sunshine itis difficult to see the marks really well so I'm going to check it again aboutdusk. but it sure seems to pull Strong so far.I didn't go full open for overa few seconds but I believe it will pretty easily turn 2850 or more.and thatshould drag this thing into the air pretty well.oil pressure seems to stay around38 or so even pretty warmat idle. head temps never went over about 284 sofar. Raymond> > > > > Read this topic online here:> > http://forums.matronics.com/viewtopic.p ... 321#310321> > > > > > > > > > ________________________________________________________________________________Subject: Pietenpol-List: Re: engine run-up
Original Posted By: "Chris"
That's great. One step closer!--------Dan PlettRead this topic online here:http://forums.matronics.com/viewtopic.p ... __________
That's great. One step closer!--------Dan PlettRead this topic online here:http://forums.matronics.com/viewtopic.p ... __________
Re: Pietenpol-List: Re: engine run-up
Original Posted By: Rick Holland
Subject: Re: Pietenpol-List: Re: engine run-up
Subject: Re: Pietenpol-List: Re: engine run-up