Page 1 of 1
Pietenpol-List: anybody near OK City?
Posted: Sat Jul 16, 2011 4:53 am
by matronics
Original Posted By: "Jack Phillips"
Subject: Pietenpol-List: anybody near OK City?This is a multi-part message in MIME format.________________________________________________________________________________
Pietenpol-List: anybody near OK City?
Posted: Sat Jul 16, 2011 8:53 am
by matronics
Original Posted By: "Gboothe5"
Hey all,I'm leaving Sunday night for Oklahoma City (Norman actually, just south)where I'll be working for about three weeks. Wanted to see if anybody is building or flying around that area who is upfor a visit.Douwe805 573 3564douweblumberg(at)earthlink.net________________________________________________________________________________
Re: Pietenpol-List: anybody near OK City?
Posted: Sat Jul 16, 2011 10:04 am
by matronics
Original Posted By: jim_markle(at)mindspring.com
OK, i know everybody is packing and dreaming of beets and fumunda arounda crackling fire, but, i'm stuck here in PA "having" to work on my Piet!i was wondering if anybody had used the caulking tube T-88 with themixing tube? it seems like a good idea for mixing large quantities ofglue, like gluing on the ply sides and bottom to the fuse.Thanks, and everybody have fun!hopefully will get out there next yearEarl--------Earl BrownI may not have gone where I intended to go, but I think I have ended up where Iintended to be.Read this topic online here:
http://forums.matronics.com/viewtopic.p ... ___Subject: Re: Pietenpol-List: anybody near OK City?
Posted: Sat Jul 16, 2011 10:39 am
by matronics
Original Posted By: "Douwe Blumberg"
I'm just an hour (well, maybe a bit more) NE of OKC so please stop by if you canwhile in the area....plenty of room if you want to come up over the weekendand hang out.JMSent via BlackBerry by AT&T-----Original Message-----
RE: Pietenpol-List: anybody near OK City?
Posted: Sat Jul 16, 2011 10:54 am
by matronics
Original Posted By: owner-pietenpol-list-server(at)matronics.com
Douwe,Does this mean you won't be at Brodhead?Jack PhillipsNX899JP "Icarus Plummet"Smith Mountain Lake, Virginia _____
Pietenpol-List: Re: Engine Run
Posted: Sat Jul 16, 2011 11:04 am
by matronics
Original Posted By: "Jack Phillips"
Well, that's too bad that you weren't able to get the beast to come to life onschedule, but overall, it sounds like you really came out on top.And in the whole story, there wasn't even one reference to "things" going missing,following a visit. Remarkable restraint on your part, Gary (and relief onthe part of JM, I'm sure).Bill C.Read this topic online here:
http://forums.matronics.com/viewtopic.p ... __________
RE: Pietenpol-List: Engine Run
Posted: Sat Jul 16, 2011 11:04 am
by matronics
Original Posted By: owner-pietenpol-list-server(at)matronics.com
I didn't pay Chris $100. He did it for $20Jack PhillipsNX899JP "Icarus Plummet"Smith Mountain Lake, Virginia _____
Pietenpol-List: Re: Engine Run
Posted: Sat Jul 16, 2011 11:20 am
by matronics
Original Posted By: "K5YAC"
Did you check Jim's big pockets ? for cookies etc.Pieti LowellDon't archive.Read this topic online here:
http://forums.matronics.com/viewtopic.p ... ___Subject: Pietenpol-List: Re: Engine Run
Pietenpol-List: Re: Engine Run
Posted: Sat Jul 16, 2011 11:39 am
by matronics
Original Posted By: "K5YAC"
If it isn't too embarrassing, could you elaborate on this comment when you gettime? > Anyhow, we determined that I had made a basic error, that may have fried my condensers,and we simply ran out of time.What mistake? How is it to be corrected? Perhaps you could just describe it over a cold one at Brodhead? I am an electronicsguy, but I didn't grow up on a farm OR sleep at a Holiday Inn Express, soI would just like to learn more about what NOT to do.--------Mark ChouinardWings, Center Section and Empannage framed up - Working on FuselageRead this topic online here:
http://forums.matronics.com/viewtopic.p ... ___Subject: Pietenpol-List: Re: Engine Run
Posted: Sat Jul 16, 2011 11:41 am
by matronics
Original Posted By: "Gboothe5"
I have no idea why my text is in BOLD after the quote... didn't mean for it tobe that way, that's just the way it appears every time I post a quote.--------Mark ChouinardWings, Center Section and Empannage framed up - Working on FuselageRead this topic online here:
http://forums.matronics.com/viewtopic.p ... __________
RE: Pietenpol-List: Re: Engine Run
Posted: Sat Jul 16, 2011 1:14 pm
by matronics
Original Posted By: owner-pietenpol-list-server(at)matronics.com
Mark,For the price of a beet, I will gladly spill the beans...But, for now, suffice it to say that the condensers connect to the NEG sideof the coils, NOT the POS side! :-O What's the fix? New condensers and movethe wires to the right side...Gary-----Original Message-----
RE: Pietenpol-List: Re: Engine Run
Posted: Sat Jul 16, 2011 1:16 pm
by matronics
Original Posted By: owner-pietenpol-list-server(at)matronics.com
Having had the opportunity to enjoy Jim's company several times, I havedevised a system to preserve the sanctity of my tools...I'm sure JM'sworking on counter-measures...Gary-----Original Message-----