Pietenpol-List: A question for Hans van der Voort

[matronics]

Original Posted By: John Fay
I say we link up and head east to Markle's place. He has a nearly complete projectthat I want to check out sometime.--------Mark - working on wingsRead this topic online here:http://forums.matronics.com/viewtopic.p ... ______Date: Mon, 27 Jul 2009 20:57:08 -0500Subject: Pietenpol-List: A question for Hans van der Voort

[matronics]

Original Posted By: hvandervoo(at)aol.com
I believe the orange and blue corvair powered Piet belonged to Gary Bell??? Great airplane. I'm wondering how the intake was plumbed - it looked like it was over the top of the engine - must have had a catch pan for flooding of carb? Which carb was used? I liked the simple installation.Tom B.________________________________________________________________________________Subject: Re: Pietenpol-List: A question for Hans van der VoortDate: Tue, 28 Jul 2009 09:18:28 -0400

[matronics]

Original Posted By: owner-pietenpol-list-server(at)matronics.com
Hans,Have you run that engine / carb setup yet? I definitely like the price!!Gary BootheCool, Ca.PietenpolWW Corvair ConversionTail done, Fuselage on gear(13 ribs down.) _____

[matronics]

Original Posted By: "TOM STINEMETZE"
Hi Guys, Don't blame the 612, the 20 deg crab to West for the full 2/3 length of36L at 12" off the deck, touching a couple times only to give the Piets behindme more room. I planted the left wheel hard on the big red circle, on the centerof the run way, when GOD sent that blast from the WEST & MY RIGHT WHEELWAS sent 12" from the edge of the runway, That entire width has got to be closeto 300 or 200 feet wide, My forward distance from the red spot was 100 Ft andto the East 100 Ft. The 612 took a 4 G stress and only just nicked the tip.The prop took most of the impact.Can some person please tell me why Ken Perkins new tail wheel that I just installedshowed a slight bend in the downward direction after this show stopper. Ifthe tail was hit hard it should have a bend upward.Thanks all for your kind considerations, All joints still work and not one sorespot this morning.And thank you for those that attended my Form, will do better next time.Pieti LowellUpdate at 11:43am... just saw the pientenpol being towed by the tail off the runway.36L should reopen soon. Hmmm.... did the tailwheel collapse, instead ofthe main? Mains looked fine on the webcam.[/quote]Read this topic online here:http://forums.matronics.com/viewtopic.p ... ______Date: Tue, 28 Jul 2009 09:14:33 -0500

[matronics]

Original Posted By: hvandervoo(at)aol.com

[matronics]

Original Posted By: owner-pietenpol-list-server(at)matronics.com
Hans,Guess I'm a little behind the power curve..What can you say about carb ice with the Zenith?Gary _____

[matronics]

Original Posted By: Ryan Mueller
Subject: Re: Pietenpol-List: Orange and blue corvair powered Piet at Brodhead

[matronics]

Original Posted By: Mark Roberts
Subject: Re: Pietenpol-List: Flying Piets in CA??yes

[matronics]

Original Posted By: owner-pietenpol-list-server(at)matronics.com
Thanks for the input, Hans. I'm sold! Do you have any installationrecommendations?One further question: Is that a WW Corvair?Gary _____

[matronics]

Original Posted By: hvandervoo(at)aol.com

[matronics]

Original Posted By: hvandervoo(at)aol.com
>> Hey guys:> I'd like to see if I can connect with any flying Piets in California... I'm> in the central part of the state (Fresno) and looking to see if there is> anything flying close enough to drive to...>> Thanks!>> Mark>> *>> " target=_blank rel=nofollow>http://www.matronics.com/Navigator?Pietenpol-List> =nofollow>http://forums.matronics.com> blank rel=nofollow>http://www.matronics.com/contribution> *>>> *>> *>>________________________________________________________________________________Subject: Re: Pietenpol-List: A question for Hans van der VoortDate: Tue, 28 Jul 2009 13:50:48 -0400